Call Us: 508.747.0300
ISO 9001:2008 - AS9100:2009 REV C CERTIFICATION

EMI/RFI Shielding

You are here:

Standard Connector and Waveguide EMI Shielding Gaskets

Standard EMI Shielding Gaskets

A wide range of products is available in a variety of materials. The most common configurations are shown. For other configurations a detailed drawing and specifications are required. These EMI shielding gaskets are available in conductive particles in elastomer Series 1000, oriented wire in elastomer Series 4000, monel foil in elastomer Series 5000 and aluminum mesh in elastomer Series 5500. Material specifications and shielding performance may be found here.


Connnector Gaskets
AN Connector Gaskets and D-Connector Gaskets are available in the following materials:
Series 1000 (conductive media on silicone elastomer)
Series 4000 (oriented aluminum or monel wires in silicone elastomer)
Series 5000 (expanded monel or aluminum foil in silicone elastomer)
Series 5500 (woven aluminum wire mesh in silicone or neoprene elastomer)


AN Connector Gaskets

AN Connector Gasket Drawing
AN Connector Gasket Drawing


How to Order


Elastomer AN
For the Elastomer Series desired, refer to the appropriate page above to specify the material and thickness. The sequential number after the material codes completes the part number. Example: Part number 5072-2050-2012 is Monoshield .020 inches thick for shell size 12 connector.
Shell Size A B C D Seq. Part No.
8 .594 .500 .875 .172 2008
10 .719 .625 1.000 .172 2010
12 .813 .750 1.094 .172 2012
14 .906 .875 1.188 .172 2014
16 .969 1.000 1.281 .172 2016
18 1.063 1.125 1.375 .203 2018
20 1.156 1.250 1.500 .203 2020
22 1.250 1.375 1.625 .203 2022
24 1.375 1.500 1.750 .203 2024
28 1.563 1.750 2.000 .203 2028
32 1.750 2.000 2.250 .219 2032
36 1.938 2.188 2.500 .219 2036
40 2.188 2.438 2.750 .219 2040
44 2.375 2.781 3.000 .219 2044
48 2.625 3.031 3.250 .219 2048
Consult factory for availability of other sizes.





D-Connector Gaskets
(Conductive Elastomers & Metalized Fabric)

D-Connector gaskets provide shielding for most 9 pin through 50 pin connectors and are available from stock in a variety of materials. For details of the materials and shielding performance, refer to the Note above. For details on Metalized Fabric 2640 Series standard gaskets, refer to this page for ordering information. Use this chart and drawing to determine the sequential number. Note: Standard 2600 Series Metalized Fabric gaskets have square corners and come with pressure sensitive tape.


How to Order


D-Connector Gaskets
For the Elastomer Series desired, refer to the appropriate page above to specify the material and thickness. The sequential number after the material codes completes the part number. Example: Part number 5072-2050-2012 is Monoshield .020 inches thick for shell size 12 connector.

Metalized Fabric D-Connector Gaskets
Use the sequential number from the chart above to complete the part number. Go to 2600 Series for complete ordering details. All standard Metalized Fabric D Connectors have Nickel over Copper Finish (1), Foam Core (1), and Pressure Sensitive Adhesive (1).
Example: Part number 2640-1111-3015-040 is a 15 pin D Connector gasket.
No. Pins A B C D E F Seq. Part No.
9 1.313 .98 .78 .44 .750 .07 R. 3009
15 1.31 .625 1.11 .44 .750 .07 R. 3015
25 2.188 1.85 1.65 .44 .750 .07 R. 3025
37 2.829 2.50 2.29 .44 .750 .07 R. 3037
50 2.740 2.41 2.11 .55 .880 .07 R. 3050
Consult factory for availability of other sizes.

D-Donnector Drawing
D-Connector Gasket Drawing





D-Connector Gaskets
(Metalized Fabric over Elastomer)


How to Order


Click here for ordering information on Standard D-Connector gaskets made from metalized fabric over elastomer.

Metalized Fabric Gasket
Metalized Fabric Gasket





D-Connector Gaskets
(Metal - Beryllium Copper / Stainless Steel)

D-Connector Gasket Drawing
D-Connector Gasket Drawing


BeCu Gasket

How to Order


Click here for D-Connector Interactive PDF Part Drawing
D-Connector Gaskets provide shielding for most 9 pin through 50 pin connectors. Independent finger design with free height of .025 for maximum surface contact provides high attenuation values with low compression forces. D-Connector Gaskets are available from stock in beryllium copper and stainless steel and can be plated in any of the finishes listed here. For details of the materials, refer here.

How to Order

Gasket A B C D E F G
9 Pin - Config.1 .44 .22 1.41 .98 .78 .16 .69
9 Pin - Config.2 .35 .18 1.41 .98 .78 .16 .69
15 Pin - Config.1 .44 .22 1.74 1.31 1.11 .16 .69
15 Pin - Config.2 .35 .18 1.74 1.31 1.11 .16 .69
25 Pin - Config.1 .44 .22 2.28 1.85 1.65 .16 .69
25 Pin - Config.2 .35 .18 2.28 1.85 1.65 .16 .69
37 Pin - Config.1 .44 .22 2.93 2.50 2.29 .16 .69
37 Pin - Config.2 .35 .18 2.93 2.50 2.29 .16 .69
50 Pin - Config.1 .55 .28 2.84 2.41 2.20 .16 .80
50 Pin - Config.2 .45 .23 2.84 2.41 2.20 .16 .80







Waveguide Gaskets
(Supershield Conductive Elastomer)

Waveguide gaskets are available from stock in conductive elastomer materials consisting of a silicone binder and a variety of conductive particles. For details of the materials and performance data refer here.

How to Order


Refer to the Supershield Page to select the material required. The sequential number after the material codes completes the part number.

Example: Part number 1052-0250-1016 is 1000 Series Supershield, standard die cut Waveguide, .020" thick, 50 durometer, 39/U model.
U.S. U.G. W.G. I.E.C. W.R. A B C D E Seq. No.
- 10 R32 284 5.857 2.878 1.372 0.274 - 1010
53/U - - - 5.312 2.878 1.372 0.281 - 1011
149A/U 12 R48 187 3.625 1.904 0.904 0.219 - 1012
344/U 14 R70 137 3.125 1.404 0.654 0.219 - 1014
39/U 16 R100 90 - 0.932 0.432 0.187 1.625 1016
419/U 18 R140 62 - 0.654 0.342 0.163 1.312 1018
595/U 20 R220 42 - 0.452 0.202 0.135 0.875 1020
599/U 22 R320 28 - 0.312 0.172 0.135 0.750 1022


Waveguide Gasket Drawing
Waveguide gaskets for plain flanges standard die cut sizes


© 2015. «Tech-Etch, Inc.». All rights reserved.
508.747.0300